ACTi E33 Instrukcja Obsługi Strona 1

Bullet Camera Series Hardware Manual E31, E32, E33, E34 Ver. 2013/12/04

www.acti.com Hardware Manual 10 Installation Procedures Mount the Camera Using the Bundled Bracket 1. Mark the location of the t

www.acti.com Hardware Manual 11 4. Depending on how you want to install the camera, attach the camera to the bracket through one o

www.acti.com Hardware Manual 12 CAUTION: If the camera will be installed outdoors, be sure to waterproof the cable connection by

www.acti.com Hardware Manual 13 Other Mounting Options In areas with fierce weather conditions, the light bundled bracket can be re

www.acti.com Hardware Manual 14 Waterproof Cable Installation The camera and the pre-installed network cable are resistant to salt

www.acti.com Hardware Manual 15 Step 1: Remove the Pre-installed Network Cable (“Pigtail”) 1. Loosen the three (3) screws to deta

www.acti.com Hardware Manual 16 Step 2: Prepare the Conduit Gland and Flex Conduit 1. Disassemble the bundled conduit gland as sh

www.acti.com Hardware Manual 17 4. Insert the sealing insert and attach it at the end of the flex conduit. Step 3: Instal

www.acti.com Hardware Manual 18 3. Secure the clamping nut to the body. NOTE: Make sure the clamping nut is tight to avoid possib

www.acti.com Hardware Manual 19 Replace the Pre-Installed Network Cable The pre-installed network cable comes with an Ethernet

www.acti.com Hardware Manual 2 Table of Contents Precautions 4 Safety Instructions ...

www.acti.com Hardware Manual 20 Step 1: Remove the Pre-installed Network Cable (“Pigtail”) 1. Loosen the three (3) screws to deta

www.acti.com Hardware Manual 21 Step 2: Install the New Ethernet Cable 1. Insert the new Ethernet cable through the sealing nut, c

www.acti.com Hardware Manual 22 5. Tighten the sealing nut. Make sure the rubber is tightly squeezed to avoid possible water leak.

www.acti.com Hardware Manual 23 Basic Connections To connect the camera, you need to prepare the following:  Power over Ethernet

www.acti.com Hardware Manual 24 Connecting Multiple Cameras To connect multiple cameras, use a PoE switch.

www.acti.com Hardware Manual 25 Accessing the Camera Configure the IP Addresses In order to be able to communicate with the camera

www.acti.com Hardware Manual 26 By double-clicking with the left mouse on the camera model, it is possible to automatically

www.acti.com Hardware Manual 27 Using the Default Camera IP Address If there is no DHCP server in the given network, the user may h

www.acti.com Hardware Manual 28 Manually adjust the IP addresses of multiple cameras: If there are more than 1 camera to be used in

www.acti.com Hardware Manual 29 Access the Camera Now that the camera and the PC are both having their unique IP addresses and are

www.acti.com Hardware Manual 3 Other Adjustments and Accessories 32 Adjust the Viewing Angle ...

www.acti.com Hardware Manual 30 The following examples in this manual are based on Internet Explorer browser in order to cover all

www.acti.com Hardware Manual 31 To check the firmware version through the Web Configurator, access the Setup page and click System

www.acti.com Hardware Manual 32 Other Adjustments and Accessories Adjust the Viewing Angle 1. Open the front cover. 2. Attac

www.acti.com Hardware Manual 33 Attach the Sunshield The use of sunshield is optional if the camera will be installed indoors. Howe

www.acti.com Hardware Manual 34 Appendix How to Make an Ethernet Cable 1. Prepare the following tools:  Ethernet cable without c

www.acti.com Hardware Manual 4 Precautions Read these instructions You should read all the safety and operating instructions before

www.acti.com Hardware Manual 5 Federal Communications Commission Statement This equipment has been tested and found to comply with

www.acti.com Hardware Manual 6 Safety Instructions Don’t open the housing of the product Cleaning Disconnect this video product fr

www.acti.com Hardware Manual 7 Introduction List of Models This hardware manual contains the following models: E31 1MP Bullet with

www.acti.com Hardware Manual 8 Package Contents Bullet Camera Sunshield Conduit Gland Mounting Screw Kit Sunshield Screw Kit Qu

www.acti.com Hardware Manual 9 Physical Description 1) Reset Button Use the Reset Button to reset the camera to its factory defa