ACTi E41 Przewodnik Instalacji

2013/12/06 Bullet with Bundled Removable Bracket Mounting on a Vertical Pole using the Accessory Set Installation Guide For Mode

www.acti.comInstallation Guide 10 2. If the camera will be installed outdoors, waterproof the cable connection by wrapping it using a moisture-se

www.acti.comInstallation Guide 11 Installation Using the Pole Mount with Bracket and Flex Conduit The D4x, E3x, E41, E41A, E42, E42A, E43, E43A ca

www.acti.comInstallation Guide 12 Step 1: Attach the Pole Mount Kit 1. Using a screwdriver, turn the screw head of the wire strap counter-clockwi

www.acti.comInstallation Guide 13 4. Position the pole mount with the cable path up and encircle the pole with the wire straps. NOTE: The wire s

www.acti.comInstallation Guide 14 2. Attach the bracket to the pole mount using the three (3) screws supplied in the pole mount kit. Step

www.acti.comInstallation Guide 15 3. Remove the pre-installed cable gland and network cable using pliers (not included in the package). Step 4:

www.acti.comInstallation Guide 16 3. From the network side, pull the Ethernet cable through the flex conduit. 4. Insert the flex conduit with E

www.acti.comInstallation Guide 17 6. Insert the sealing insert and attach it at the end of the flex conduit. Step 5: Install the Etherne

www.acti.comInstallation Guide 18 Step 6: Connect the Ethernet Cable 1. Connect the Ethernet cable to the Ethernet port inside the camera. 2.

www.acti.comInstallation Guide 19 2. Attach the two (2) screws (supplied in the heavy duty bracket package) to secure the camera to the holder.

www.acti.comInstallation Guide 2 Table of Contents Installation Procedures ... 4 Installation Us

www.acti.comInstallation Guide 20 5. As needed, turn the holder left or right to adjust the camera viewing direction. Then, secure the screw tigh

www.acti.comInstallation Guide 21 Installation Using the Pole Mount with Bracket and Naked Cable The pre-installed network cable comes with an Eth

www.acti.comInstallation Guide 22 Step 1: Attach the Pole Mount Kit 1. Using a screwdriver, turn the screw head of the wire strap counter-clockwi

www.acti.comInstallation Guide 23 4. Position the pole mount with the cable path up and encircle the pole with the wire straps. NOTE: The wire s

www.acti.comInstallation Guide 24 2. Attach the bracket to the pole mount using the three (3) screws supplied in the pole mount kit. Step 3

www.acti.comInstallation Guide 25 4. Squeeze the seal to pull out the connector and then completely remove the seal, claw, and sealing nut from t

www.acti.comInstallation Guide 26 3. Attach the RJ-45 connector to the Ethernet cable. See How to Make an Ethernet Cable on page 42. 4. Connect

www.acti.comInstallation Guide 27 Step 5: Install the Camera 1. Align the screw holes of the holder to the bottom screw holes of the camera. 2.

www.acti.comInstallation Guide 28 4. Loosely attach the screw to secure the holder to the bracket. 5. As needed, turn the holder left or right

www.acti.comInstallation Guide 29 Step 6: Connect the Camera to the Network Connect the other end of the Ethernet cable to a PoE switch. Step 7:

www.acti.comInstallation Guide 3 How to Make an Ethernet Cable ... 42 Safety Information

www.acti.comInstallation Guide 30 Appendices How to Access the Camera Live View Connect the Equipment To be able to connect to the camera firmwar

www.acti.comInstallation Guide 31 The quickest way to discover the cameras in the network is to use the simplest network search, built in

www.acti.comInstallation Guide 32 If you work with our cameras regularly, then there is even a better way to discover the cameras

www.acti.comInstallation Guide 33 Use the default camera IP address: If there is no DHCP server in the given network, the user may have to assign

www.acti.comInstallation Guide 34 Manually adjust the IP addresses of multiple cameras: If there are more than 1 camera to be used in the same loc

www.acti.comInstallation Guide 35 Access the Camera Now that the camera and the PC are both having their unique IP addresses and are under the sam

www.acti.comInstallation Guide 36 The following examples in this manual are based on Internet Explorer browser in order to cover all functions of

www.acti.comInstallation Guide 37 To check the firmware version through the Web Configurator, access the Setup page and click System > System I

www.acti.comInstallation Guide 38 How to Adjust Focus This section describes the procedures in adjusting the viewing angle and focus of the differ

www.acti.comInstallation Guide 39 3. Attach the lens focus tuner to the lens. D3x Series E3x Series 4. Adjust

www.acti.comInstallation Guide 4 Installation Procedures The camera can be installed onto a pole using additional mounting accessories. The access

www.acti.comInstallation Guide 40 D4x / E41 / E41A / E42 / E42A / E43 / E43A Series 1. Open the front cover. 2. Based on the live view fro

www.acti.comInstallation Guide 41 How to Attach the Sunshield The use of sunshield is optional if the camera will be installed indoors. However, i

www.acti.comInstallation Guide 42 How to Make an Ethernet Cable 1. Prepare the following tools:  Ethernet cable without connectors  RJ-45 Con

www.acti.comInstallation Guide 43 Safety Information Read these instructions You should read all the safety and operating instructions before usin

www.acti.comInstallation Guide 44 Damage Requiring service Disconnect this video product from the power supply immediately and refer servicing to

www.acti.comInstallation Guide 5 Installation Using the Pole Mount with Bracket and Sealant Tape Step 1: Attach the Pole Mount Kit 1. Using a

www.acti.comInstallation Guide 6 4. Position the pole mount with the cable path up and encircle the pole with the wire straps. NOTE: The wire st

www.acti.comInstallation Guide 7 2. Attach the bracket to the pole mount using the three (3) screws supplied in the pole mount kit. Step 3

www.acti.comInstallation Guide 8 3. Align the screw hole of the holder to the heavy duty bracket. 4. Loosely attach the screw to secure the h

www.acti.comInstallation Guide 9 6. As needed, turn the holder left or right to adjust the camera viewing direction. Then, secure the screw tight