ACTi E77 Instrukcja Obsługi

4” Outdoor Dome Series Hardware Manual D71A, D81A, D82A, E74A, E75, E76, E77 E82A, E83A, E84A, E86A, E88 2014/01/15

www.acti.com Hardware Manual 10 4) Digital Input / Output (DI/DO) and Audio Input / Output This connector connects to digital input

www.acti.com Hardware Manual 11 Mounting Options There are several mounting options that you can use to install the camera. Select t

www.acti.com Hardware Manual 12 Straight Wall Mount Suitable when mounting the camera on straight walls. PMAX-0308 (L-Type Wall Mou

www.acti.com Hardware Manual 13 Other Mounting Accessories Accessories PMAX-0104 (Extension Tube) PMAX- 0700 (Junction Box) NOTE

www.acti.com Hardware Manual 14 Installing the Camera on a Surface This section describes the procedures in installing the camera on

www.acti.com Hardware Manual 15 Step 2: Open the Dome Cover NOTE: To avoid scratches or leaving fingerprints on the dome cover, it i

www.acti.com Hardware Manual 16 3. Carefully lift to open the dome cover and place it on the side of the camera. NOTE: Do not abrup

www.acti.com Hardware Manual 17 Step 3: Prepare for Waterproof Installation The camera comes with two (2) glands used for waterproof

www.acti.com Hardware Manual 18 Waterproof Solution with Naked Cable This section describes the procedures in using the bundled cabl

www.acti.com Hardware Manual 19 4. Attach the cable gland body to the hole of the camera. Attach to Camera Side Hole

www.acti.com Hardware Manual 2 Table of Contents Precautions ... 4 Safety

www.acti.com Hardware Manual 20 Waterproof Solution with Conduit This section describes the procedures to waterproof the cabling con

www.acti.com Hardware Manual 21 3. Pull the network cable through the flex conduit. If connecting other input/output devices or an

www.acti.com Hardware Manual 22 6. Screw the conduit gland body to the conduit hole of the camera. Attach to Side Conduit Ho

www.acti.com Hardware Manual 23 8. If connecting other cables, attach the terminal blocks to the cables. See Other Connections on p

www.acti.com Hardware Manual 24 Step 4: Install the Camera to the Surface Align the camera screw holes and the conduit hole (if nece

www.acti.com Hardware Manual 25 Step 5: Connect the Cable(s) 1. If the cables will be routed along the surface, pull the network ca

www.acti.com Hardware Manual 26 3. Connect the other end of the network cable to a switch or injector. Then, connect the switch or

www.acti.com Hardware Manual 27 Step 8: Close the Dome Cover 1. Align the position of the dome cover shroud to the direction of the

www.acti.com Hardware Manual 28 Other Connections This section describes the procedures in preparing the Digital Input and Output (D

www.acti.com Hardware Manual 29 Press and hold the orange tab as you insert the wire through the pin slot, then release the orange t

www.acti.com Hardware Manual 3 Other Adjustments and Accessories ... 33 How to Adjust the Viewing Angle ...

www.acti.com Hardware Manual 30 Typical Connection Based on these specifications, if the DI device has a voltage of 0V ~ 30V or the

www.acti.com Hardware Manual 31 The illustration below is a graphic example of connecting a relay to a high voltage DO device. Rela

www.acti.com Hardware Manual 32 How to Connect Audio Devices Audio input / output devices, such as an active microphone or speaker c

www.acti.com Hardware Manual 33 Other Adjustments and Accessories How to Adjust the Viewing Angle This section describes the procedu

www.acti.com Hardware Manual 34 1. Loosen the tilt adjustment screws, adjust the tilt, and then tighten back the screws to fix the

www.acti.com Hardware Manual 35 D8xA / E8xA Series Camera Parts Overview Adjustment Procedures 1. Loosen the tilt adjustment scre

www.acti.com Hardware Manual 36 How to Install / Remove the Memory Card The camera supports local video recording or saving of snaps

www.acti.com Hardware Manual 37 How to Replace the Dome Cover For more discrete surveillance needs, the bundled dome cover can be re

www.acti.com Hardware Manual 38 4. Remove dome cover from the cover housing. 5. Remove the shroud from the dome cover. 6. I

www.acti.com Hardware Manual 39 8. Align and attach the three (3) screws to secure the bracket to the cover housing. 9. Fit t

www.acti.com Hardware Manual 4 Precautions Read these instructions You should read all the safety and operating instructions before

www.acti.com Hardware Manual 40 Accessing the Camera Configure the IP Addresses In order to be able to communicate with the camera f

www.acti.com Hardware Manual 41 Double-click the mouse button on the camera model name, the default browser of the PC is

www.acti.com Hardware Manual 42 Use the default IP address of a camera: If there is no DHCP server in the given network, the user ma

www.acti.com Hardware Manual 43 Manually adjust the IP addresses of multiple cameras: If there are more than 1 camera to be used in

www.acti.com Hardware Manual 44 Access the Camera Now that the camera and the PC are both having their unique IP addresses and are u

www.acti.com Hardware Manual 45 Assuming that the camera’s IP address is 192.168.0.100, you can access it by opening the Web browser

Copyright © 2014, ACTi Corporation All Rights Reserved 7F, No. 1, Alley 20, Lane 407, Sec. 2, Ti-Ding Blvd., Neihu Di

www.acti.com Hardware Manual 5 Federal Communications Commission Statement This equipment has been tested and found to comply with t

www.acti.com Hardware Manual 6 Safety Instructions Cleaning Disconnect this video product from the power supply before cleaning. At

www.acti.com Hardware Manual 7 Introduction The List of Models This hardware manual contains the following models: D71A 1MP Outdoor

www.acti.com Hardware Manual 8 Ou Package Contents Camera Mounting Screw Kit Hexagon Screwdriver Drill Template Conduit Gland Ca

www.acti.com Hardware Manual 9 Physical Description NOTE: The camera picture above is for reference only. Actual camera may slightl