Acti Indoor Dome (B6x) on Tilted Wall Instrukcja Użytkownika

2014/01/10 Indoor Zoom Dome Mounting on the Wall with Flat Surface (Face Forward) Installation Guide For Models: B61, B64, B65, B67

www.acti.comInstallation Guide 10 Appendices How to Access the Camera Live View Connect the Equipment To be able to connect to the camera firmware

www.acti.comInstallation Guide 11 The quickest way to discover the cameras in the network is to use the simplest network search, built in

www.acti.comInstallation Guide 12 The IP Utility can be downloaded for free from http://www.acti.com/IP_Utility With just one click, you can launc

www.acti.comInstallation Guide 13 Manually adjust the IP address of the PC: In the following example, based on Windows 7, we will configure the IP

www.acti.comInstallation Guide 14 Manually adjust the IP addresses of multiple cameras: If there are more than 1 camera to be used in the same loc

www.acti.comInstallation Guide 15 Access the Camera Now that the camera and the PC are both having their unique IP addresses and are under the sam

www.acti.comInstallation Guide 16 Assuming that the camera’s IP address is 192.168.0.100, you can access it by opening the Web browser and typing

www.acti.comInstallation Guide 17 How to Connect the Power Adapter (Optional) In case of using a non-PoE switch or your PoE switch has limited pow

www.acti.comInstallation Guide 18 3. Connect the wire with the white stripe to the 12V pin and the other to the GND pin. 4. Tighten the scr

www.acti.comInstallation Guide 19 How to Connect DI/DO Devices (Optional) Depending on your surveillance needs, you may connect digital input or o

www.acti.comInstallation Guide 2 Table of Contents Installation Procedures ... 3 Step 1: Drill t

www.acti.comInstallation Guide 20 To connect output devices (DO), map the pins to one of the pin combinations below: Device Pin Mapping Instruct

www.acti.comInstallation Guide 21 High Voltage DO Device Connection Even though the camera provides 12V power, this may not be enough for some hig

www.acti.comInstallation Guide 22 How to Connect Audio Devices (Optional) Depending on your surveillance needs, you may connect an audio input or

www.acti.comInstallation Guide 23 Safety Information Read these instructions You should read all the safety and operating instructions before usin

www.acti.comInstallation Guide 24 Damage Requiring service Disconnect this video product from the power supply immediately and refer servicing to

Copyright © 2014, ACTi Corporation All Rights Reserved 7F, No. 1, Alley 20, Lane 407, Sec. 2, Ti-Ding Blvd., Neihu Di

www.acti.comInstallation Guide 3 Installation Procedures This section describes the procedures in installing the camera directly on the wall. Prep

www.acti.comInstallation Guide 4 Step 2: Open the Dome Cover NOTE: To avoid scratches or leaving fingerprints on the dome cover, it is recommended

www.acti.comInstallation Guide 5 Step 3: Install the Camera to the Surface 1. If necessary, insert a memory card, with the metallic contacts faci

www.acti.comInstallation Guide 6 Step 4: Connect the Cable(s) 1. Connect the network cable to the Ethernet port of the camera. If necessary, conn

www.acti.comInstallation Guide 7 Step 5: Access the Camera Live View See How to Access the Camera Live View on page 10 for more information on how

www.acti.comInstallation Guide 8 2. Loosen the rotation adjustment screw, rotate the viewing orientation, and then tighten back the screw to fix

www.acti.comInstallation Guide 9 3. Remove the plastic covering the dome cover. Final installation should look similar to the illustration be